What is the Transformer’s Voltage Regulation?

Electrical Technology

Voltage Regulation of Transformer- Formulas and Examples

Table of Contents

What is Voltage Regulation?

Transformer’s voltage regulation is the ratio of the difference between transformer no load and full load output voltage to its full load output voltage expressed as a percentage (%).

In other words, transformer voltage regulation is the measure of supplying constant output voltage with different load currents.

In simple words, the change in magnitude of input and output voltage of the transformer is know as voltage regulation. i.e. the change in transformer secondary terminal voltage from no load to full load related to the no load voltage is known as “voltage regulation”.

Mathematically, the voltage regulation is expressed by the following formula.

Voltage regulation for primary winding of the transformer

Where:

E₁ = No load primary terminal voltage
V₁ = Full load primary terminal voltage
E₂ = No load secondary terminal voltage
V₂ = Full load secondary terminal voltage

A Transformer will generally provide a higher output voltage at no load than when the transformer is fully loaded according to the transformer nameplate data rating capacity. Stated differently, under load, a transformer’s output voltage drops slightly.

Power transformer should provide a constant output voltage (ideally as it is not possible in real). So it is the better option to have as much as little variation in output voltage with different load currents. In this scenario, voltage regulation shows that how much a transformer can provide a constant secondary voltage with different loads connected to the transformer output.

The following basic transformer circuit and solved example will clear the concept of transformer’s voltage regulation.

In first scenario, Suppose there is no load connected to the transformer’s secondary, In this case of open circuit:

No load current is flowing due to open circuit.
When no load current flows, there is no voltage drop and reactive drops across resistor and inductors respectably.
Voltage drops across primary terminals are negligible.

In second scenario, the transformer is loaded i.e. there is a load connected to the secondary terminals of the transformer. In this case of loaded circuit:

Load current is flowing due to completed circuit and load connected to the secondary terminals.
Load current flows through the load, so there must be voltage drops across resistors and inductors.
This way, the average value of voltage regulation is more than that of transformer at no load.

For better performance, voltage regulation should be low (ideal zero), i.e. the higher the voltage regulation, the worst of the transformer’s efficiency and performance will be.

The above circuit and explanation, following two points are concluded:

In a transformer, the value of primary voltage is always greater than the induced EMF in the primary windings.

V₁> E₁

In a transformer, the value of secondary terminal voltage at no load is always greater than the secondary terminal voltage at full load.

E₂> V₂

Based on the above information from the mentioned circuit diagram, the following two equations can be made:

V₁ = I₁R₁ Cosθ₁+ I₁X₁ Sinθ₁ + E₁
E₂ = I₂R₂ Cosθ₂+ I₂X₂ Sinθ₂ + V₂

For various kind of loads i.e. inductive and capacitive loads etc, the following expression at no load secondary voltage.

Following are the expression of no load secondary voltage for various kind of loads i.e. inductive and capacitive loads etc.

Related Post: What is the Average Life Expectancy of a Transformer ?

Voltage Regulation for Inductive Loads (Lagging Power Factor)

E₂ = I₂R₀₂ Cosθ₂+ I₂X₀₂ Sinθ₂ + V₂

E₂ – V₂ = I₂R₀₂ Cosθ₂+ I₂X₀₂ Sinθ₂

Transformer’s voltage regulation at lagging power factor (Inductive Load):

Voltage Regulation for Capacitive Loads (Leading Power Factor)

E₂ = I₂R₀₂ Cosθ₂– I₂X₀₂ Sinθ₂ + V₂

E₂ – V₂ = I₂R₀₂ Cosθ₂– I₂X₀₂ Sinθ₂

Transformer’s voltage regulation at leading power factor (Capacitive Load):

Where:

(I₂R₀₂ / E₂) x 100 is a percentage resistance drop
(I₂X₀₂ / E₂) x 100 is a percentage reactance drop

Related Post: EMF Equation of a Transformer

Examples of Voltage Regulation

Example 1:

Suppose a transformer has a no load voltage of 240 volts and a full load voltage of 230 volts. The transformer’s Regulation is calculated as follows.

% Voltage Regulation = [{(No Load Voltage – Full Load Voltage) / Full Load voltage} x 100]

% Voltage Regulation = [{(240V – 230V) / 230} x 100]

% Voltage Regulation = 4.347%

Not happy with the basic one example as above, lets go little bit complex as follow.

Related Post: Transformer Losses – Types of Energy Losses in a Transformer

Example 2:

A 50kVA transformer has 200 turns and 40 turns on the primary and secondary windings respectively. Resistance on primary and secondary are 0.15 Ω and 0.005 Ω respectively. The value of leakage reactances on primary and secondary windings are 0.55 and 0.0175 Ω respectively. If the supply voltage on the primary side is 1100V, Calculate:

Equivalent impedance transferred to Primary Windings
Secondary terminal Voltage at Full load having a lagging power factor of 0.8.
Voltage regulation

Solution:

Given Data:

Primary Voltage: 1100V
Primary Turns: 200
Secondary Turns: 40
R₁ = 0.15 Ω
R₂ = 0.005 Ω
X₁ = 0.55 Ω
X₂ = 0.0175 Ω
Power Factor = Cos θ = 0.8 Lagging

(1)

Turn ratio = K = N₂ / N₁ = 40 / 200 = 1/5

R₀₁ = R₁ + R₂/ K² = 0.15Ω + 0.005Ω / (1/5)² = 0.275 Ω

X₀₁ = X₁ + X₂ / K² = 0.55Ω + 0.0175Ω / (1/5)² = 0.987 Ω

Z₀₁ = 0.275 + j 0.987 = 1.025 ∠74.43^o

Z₀₂ = K²Z₀₁ = (1/5)² (0.275 + j 0.987) = (0.011 + j 0.039)

(2)

No-load secondary voltage = KV₁ = (1/5) × 1100V = 220 V

Secondary current: I₂ = 50 x10³/220V = 227.27 A … (I = P/V = 50kVA / 220V)

I₂ = 227.27 A

Full-load voltage drop as referred to secondary

= I₂ (R₀₂ Cos θ + X₀₂ Sin θ)

= 227.27 A (0.011 × 0.8 – 0.039 × 0.6) = – 3.32 V

Secondary terminal voltage on load = 220V – 3.32V = 216.68 V

Full Load Secondary Voltage: 216.68 V

(3)

% Regulation = 3.32V × 100/220 = 1.51

Voltage Regulation:

% Voltage Regulation = (V_{No load} – V_{Full Load} / V_{Full Load}) x 100

= (220V – 216.68V / 216.68V) x 100 = 1.53

% Voltage Regulation = 1.53

Related Post: Open Delta Connections of Transformers

Transformer’s Zero Voltage Regulation

Zero voltage regulation means the “no load voltage” and “full load voltage” of the transformer is equal i.e. there is no difference between them. Zero voltage regulation indicates the highest possible performance of a transformer which is only possible in an theoretical and ideal transformer.

Apart the theory, the lower the voltage regulation percentage, the more stable and constant the secondary terminal voltage to the loads with better regulation.

Related Post: Types of Transformers and Their Applications

Applications of Poor Regulation

There are some applications where we need poor transformer voltage regulation such as a “discharge lamp”. In this case, a step up transformer is needed to provide a high voltage at the initial stage to ignite the lamp and then drop off the level of voltage after ignition and current starts to flow in the discharge lighting circuit. This process can be nicely done through a step up transformer having poor regulation (high % of voltage regulation).

similarly, poor voltage regulation are needed in arc welding machines which is actually a step down transformer providing low voltage and high current to the arc welding process.

Good to Know: High % Voltage Regulation means poor regulation or performance.

Related Post: Current Transformers (CT) – Types, Characteristic & Applications

How to Improve the Transformer Regulation?

A device known as ferroresonant transformer (a combination of transformer and LC resonant circuit) is used to improve the transformer regulation (i.e. reduce the percentage of voltage regulation of a transformer). The iron core of ferroresonant transformer is full of flux (magnetic lines) for large portion of the AC cycle. This way, the transformer primary current and variation in supply voltage have little effect on the transformer’s core magnetic flux density. It means the transformer’s secondary terminals output is almost constant voltage without being affected by major variation in the supply voltage to the primary windings of the transformer.